RETIRED ›
This product is no longer available and has been replaced by: RV50.
RAVENXTV Cellular Digital Modem for Verizon
Services Available
Repair No
Calibration No
Free Support No

Overview

The RavenXTV is a 3G cellular gateway for Verizon Wireless. The RavenXTV has an RS-232 serial interface for configuration and deployment with Campbell Scientific data loggers and peripherals.

Internet Connectivity

The RavenXTV provides Internet connectivity to any of our data loggers located within range of a compatible cellular network. With Internet connectivity, a data logger can transmit data to, and be remotely administered by, Campbell Scientific software. The RavenXTV can also enable many data loggers to communicate using other Internet protocols, such as email and web (HTTP).

Device Intelligence

The RavenXTV is powered by Sierra Wireless’s ALEOS embedded operating system. This allows the RavenXTV to provide highly reliable connectivity and remote device management independent of the device it is connected to. The embedded applications include IP serial server and client, local PPP host, dynamic DNS client, performance monitoring, IPsec VPN, and GRE tunneling.

Read More

Benefits and Features

  • Internet connectivity using high-speed 3G cellular networking
  • Low power consumption without sacrificing device intelligence
  • Compatible with most Campbell Scientific data loggers
  • Rugged design with wide operating temperature and Class I Division 2 compliance

Images

Detailed Description

Before purchasing the RavenXTV, verify that EV-DO / CDMA coverage is available at your site(s) by contacting Verizon. Refer to the Compatibility information on the web page regarding establishing cellular service.

Specifications

Technology 3G EV-DO Rev. A (with fallback to CDMA 1x Rev. 0, CDMA 1xRTT, CDMA IS-95)
Dual Band 800 MHz Cellular, 1900 MHz PCS
Transmit Frequency 1850 to 1910 MHz and 824 to 849 MHz
Transmit Power
  • 1 W for 1900 MHz
  • 0.8 W for 850 MHz
Receiver Frequency 1930 to 1990 MHz and 869 to 894 MHz
CDMA Throughput Up to 80 kbps
RS-232 Data Rates 1200 bps to 115.2 kbps
Serial Interface RS-232, DB9-F
Serial Protocols AT Commands, PPP, SLIP, UDP/IP, TCP/IP
RF Antenna Connector 50 Ω SMA
Input Current Range 40 to 250 mA
Input Voltage Range 6 to 28 Vdc
Status LEDs Power, Network, Signal, Activity
Operating Temperature Range -30° to +65°C
Operating Humidity 5% to 95% RH (non-condensing)
Typical Current Drain
  • 50 mA (at 12 Vdc when dormant, which is idle for 10 to 20 s)
  • 120 mA (transmit/receive)
Dimensions 10 x 7.6 x 2.5 cm (4 x 3 x 1 in.)
Weight < 0.5 kg (< 1 lb)

Compatibility

Note: The following shows notable compatibility information. It is not a comprehensive list of all compatible or incompatible products.

Data Loggers

Product Compatible Note
21X (retired) An SC105 or SC932A is required to connect the RavenXTV to the CS I/O port of the data logger.
CR10 (retired) An SC105 or SC932A is required to connect the RavenXTV to the CS I/O port of the data logger.
CR1000 (retired)
CR10X (retired) An SC105 or SC932A is required to connect the RavenXTV to the CS I/O port of the data logger.
CR200X (retired)
CR206X (retired)
CR211X (retired)
CR216X (retired)
CR23X (retired)
CR295X (retired)
CR300 Use a 18663 null modem cable.
CR3000 (retired)
CR310 Use a 18663 null modem cable.
CR500 (retired) An SC105 or SC932A is required to connect the RavenXTV to the CS I/O port of the data logger.
CR5000 (retired)
CR510 (retired) An SC105 or SC932A is required to connect the RavenXTV to the CS I/O port of the data logger.
CR6
CR800 (retired)
CR850 (retired)
CR9000 (retired) Although the CR9000 is compatible, the RavenXTV does not support its fastest communication rates, and therefore may not be practical for many CR9000 applications.
CR9000X (retired) Although the CR9000X is compatible, the RavenXTV does not support its fastest communication rates, and therefore may not be practical for many CR9000X applications.

Mounting Equipment

Product Compatible Note
ENC10/12
ENC10/12R
ENC12/14
ENC14/16
ENC16/18

Additional Compatibility Information

Establishing Cellular Service

Call Verizon at 1-888-384-1775 and ask to speak to an M2M (machine-to-machine) account sales expert for the purpose of setting up either a static or dynamic IP account. A static IP account eliminates the need for a third-party Dynamic Domain Name System (DDNS), such as IP manager. The DDNS translates the domain name to a dynamic IP address so that the modem can be contacted as if it had a static IP address.

When setting up the account, you will need the ESN number, which is listed on the modem’s label. You will also need to request the unrestricted IP. Verizon’s Broadband Plan is also recommended.

Configuring the Modem

The RavenXTV is configured using Campbell Scientific’s Device Configuration Utility. Device Configuration Utility simplifies configuration of the modem parameters.

Alternatively, a RavenXTV that has been successfully connected to the Internet can be configured using a web browser. Using your web browser, navigate to http://your.devices.address:9191.

Data Logger Considerations

The modem connects to the data logger's RS-232 port via a 9-pin male-to-male null modem cable; Campbell Scientific offers the 18663 null modem cable (see Ordering). Alternatively, the modem can be connected to the data logger's CS I/O port, but an SC105 or SC932A interface is required.

Power Considerations

A power cable included with the modem connects to the data logger’s 12 V or switched 12 V terminal. Connection to the switched 12 V terminal allows the data logger to switch power to the modem during scheduled transmission intervals, thereby conserving power. Alternatively, the modem can be powered directly from a battery or one of our charging regulators. For help with analyzing your system’s power requirements, refer to our "Power Supply Overview" or "Power Supplies" application note.

Enclosure Considerations

A desiccated, non-condensing environment is required. The 14394 Mounting Kit includes hardware for securing the RavenXTV to an enclosure backplate (see Ordering Info).

Downloads

Device Configuration Utility v.2.30 (46.9 MB) 10-02-2024

A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.

Supported Operating Systems:

Windows 11 or 10 (Both 32 and 64 bit)

View Update History

Frequently Asked Questions

Number of FAQs related to RAVENXTV: 15

Expand AllCollapse All

  1. Yes. These modems have an input voltage range of 6 to 28 Vdc.

  2. Yes. Both modems connect to a data logger using an RS-232 9-pin connector for their communication.

  3. No. A dipole antenna, such as the 21831, transmits a short distance, emitting a signal 360° around the antenna plain. To transmit to a distant point, a Yagi antenna, such as the 10530, is a more appropriate option.

  4. No. A half-wave antenna may not work in the transmission area. Several antenna options, however, are available for purchase:

    • 21831 – a half-wave dipole whip antenna
    • 18285 – a dual-band, omnidirectional antenna
    • 20679 – a dual-band, omnidirectional antenna
    • 10530 – a high-gain, directional (Yagi) antenna
  5. A standard null modem cable can be used to connect a RavenXT-series modem to the data logger RS-232 port. Alternatively, an SC12 cable and an SC105 interface can be used to connect the RavenXT-series modem to the data logger CS I/O port.

  6. There are three main reasons that a data logger might lose communication over a cellular modem:

    • Loss of power
    • Physical damage
    • Network service issues

    Contact Campbell Scientific for assistance with troubleshooting.

  7. Using an SC105 with a RavenXTV or RavenXTG cellular modem allows for the two devices to communicate at differing baud rates. It also allows for other devices, such as an RF401 radio or CR1000KD handheld display, to simultaneously be connected to the data logger’s CS I/O port.

  8. To connect the modem to the data logger’s CS I/O port, either the SC932A or the SC105 must be used.  This communication also depends on the configuration of the ports on the modem and data logger (PPP versus serial server); the two must match.

  9. For the data logger to transfer data via FTP, the modem has to be set up to use a PPP connection between it and the data logger.

Case Studies

Pennsylvania: Flood Warning
Flooding is the number one natural cause of fatalities worldwide and was responsible for 6.8......read more
Arkansas: Flood Warning
Hot Springs, Arkansas, is a history-rich city located adjacent to Hot Springs National Park. The......read more

Articles and Press Releases


This Product Replaced

Privacy Policy Update

We've updated our privacy policy.  Learn More

Cookie Consent

Update your cookie preferences.  Update Cookie Preferences