HygroVue 5 Digital Temperature and Relative Humidity Sensor
Designed for General Meteorological and Other Data Logging Applications
weather applications water applications energy applications gas flux and turbulence applications infrastructure applications soil applications

Overview

The HygroVue™5 Temperature and Relative Humidity Sensor is designed for general meteorological and environmental monitoring applications. It uses the SDI-12 communications protocol to communicate with any SDI-12 recorder, simplifying installation and programming. The sensing element is easily changed in the field, reducing downtime and calibration costs. It is the entry-level sensor in the HygroVue™ line of relative humidity and temperature sensors.

Read More

Benefits and Features

  • Uses a combined, pre-calibrated digital humidity and temperature element
  • Field-changeable element for fast, on-site recalibration
  • Digital SDI-12 output, allowing long cables with no added errors
  • Simple data logger programming
  • Low power consumption
  • Wide operating voltage
  • Rugged design with potted electronics
  • Compact size for smaller radiation shields

Images

HygroVUE™5 installed in a shield and mounted (items sold separately)

Detailed Description

The HygroVue 5 sensor has a user-replaceable chip element that incorporates both a temperature sensor and an RH sensor. Each element is individually calibrated with the calibration corrections stored on the chip.

Electronics within the HygroVue 5 control the measurement made by the sensor element, apply temperature and linearization corrections to the readings, and present the data via SDI-12 to a data logger.

A stainless-steel mesh filter minimizes the effects of dust and dirt on the sensor, while allowing air exchange around the sensor element and reducing the chance that condensation remains inside the filter cap. A small PTFE membrane filter is bonded to the surface of the element, which prevents any finer dust or mold from directly influencing the measurement.

The sensor housing is designed to withstand permanent exposure to all weather. It fits into a range of radiation shields, including compact shields such as the RAD06 6-Plate Solar Radiation Shield.

For improved reliability, the sensor is factory fitted with a fixed length of cable, and the sensor body is then potted to completely seal the electronics and cable joint. A range of cable lengths is available.

Specifications

Sensing Element SHT35 derivative (specially coated for reliability)
Calibration Traceability NIST and NPL standards
Supply Voltage 7 to 28 Vdc
Warm-up Time Sensor is normally powered all the time. If power is switched off, allow 1.8 s for sensor to power up.
Main Housing Material White PET-P
Housing Classification IP67 (electronics housing)
Sensor Protection Outer glass-filled polypropylene cap fitted with a stainless-steel mesh dust filter with nominal pore size of < 30 µm. The sensor element is fitted with a PTFE protective film with a filtration efficiency of > 99.99% for particles of 200 nm or larger size.
EMC Compliance Tested and conforms to IEC61326:2013
Calibration The sensor element is individually calibrated during manufacture.
Field-Replaceable Chip or Recalibrate Field-replaceable chip
Diameter 12.5 mm (0.49 in) at sensor tip, maximum 16 mm (0.63 in) at the cable end
Length 115 mm (4.52 in) sensor only, without cable

Maximum Current Drain

Quiescent 50 μA typical
During Measurement 0.6 mA (takes 0.5 s) typical

Air Temperature

Measurement Range -40 to +70°C
Accuracy
  • ±0.4°C (over the range -40 to +70°C)
  • ±0.3°C (over the range 20 to 60°C)
Long-Term Drift < ±0.03°C per year
Reported Resolution 0.001°C
Repeatability 0.04°C Values are 3 standard deviations of 25 measurements at constant temperature.
Response Time 130 s (63% response time in air moving at 1 m/s)
Units Degrees Celsius

Relative Humidity

Measurement Range 0 to 100% RH
Accuracy
  • ±1.8% (at 25°C, over the range 0 to 80% RH)
  • ±3% (at 25°C, over the range 80 to 100% RH)
Additional Errors at Other Temperatures < ±1% RH (over -40 to +60°C)
Short-Term Hysteresis < ±1% RH
Long-Term Stability ±0.5% per year (maximum drift in clean air conditions)
Reported Resolution 0.001% RH
Repeatibility 0.05% RH Values are 3 standard deviations of 25 measurements at constant humidity.
Response Time with Filter 8 s (63% response time in air moving at 1 m/s at 25°C)

Compatibility

Note: The following shows notable compatibility information. It is not a comprehensive list of all compatible or incompatible products.

Data Loggers

Product Compatible Note
CR1000 (retired)
CR1000X
CR300
CR3000 (retired)
CR310
CR350
CR6
CR800 (retired)
CR850 (retired)

Additional Compatibility Information

Digital SDI-12 output which is fully SDI-12 V1.3 compliant (verified with an SDI-12 Verifier (www.sdi-12-verifier.com/). It is compatible with SDI-12 V1.4 recorders.

Case Studies

South Africa: Sustainable Solutions for Farms
International partnerships for sustainable innovations Improved water use in agriculture is essential to successfully adapt to......read more
South Africa: Fog Harvesting
Southwestern South Africa had three consecutive dry winters—from 2015 through 2017—resulting in the Cape Town......read more
South Africa: Launch of an Innovative Science Facility with Sustainable Technology
The Department of Science and Innovation (DSI) and its partners, including the Department of Basic......read more
South Africa: Transforming a Polluted River
The Jukskei River is one of the largest rivers in Johannesburg, South Africa. The river......read more

Articles and Press Releases

Blog Articles


Listed Under

Common Accessory for the following products:
This Product Replaced

Privacy Policy Update

We've updated our privacy policy.  Learn More

Cookie Consent

Update your cookie preferences.  Update Cookie Preferences